Intact Battery-Guard

€21,99
| /
Bestellung 14.07.
Lieferung 15.07. – 17.07.

Easy battery monitoring via Bluetooth and app

With the intAct Battery Guard you can easily and simply monitor the charge status of your battery. The battery monitor can be used for all 12 volt lead-acid batteries (i.e. wet batteries, EFB batteries, AGM batteries and GEL batteries) and lithium batteries (LiFePO4). In addition to the battery voltage in volts, the voltage monitor also transmits the current housing temperature and uses an intelligent algorithm to calculate the charge level corresponding to the overall condition of your battery. The data is stored on the battery tester for up to 72 days and transferred to the smartphone the next time it is connected.

To ensure you can use Battery Guard as quickly as possible, please note the following instructions:

Install the app and grant permissions

Before you attach your battery monitor to your battery, download the " intAct Battery-Check " app from the App Store or Google Play Store and install it on your smartphone. Don't be alarmed: In addition to the obviously necessary Bluetooth(R) permission, the app also requires your location permission. This is not because we want to monitor you. The app needs this to scan for Bluetooth(R) devices (i.e. battery guards) in your area.

Setting up Battery Guard in the app

After you have successfully installed the app, scan the barcode of the Battery Guard (not the one on your battery) or enter the corresponding serial number manually in the app. This registers the test device in the app and allows you to give each device an individual name. In doing so, you also tell the app the battery type (wet battery, AGM, gel or lithium) and can choose between the values ​​specified by the algorithm or individual battery settings.

Attach the battery tester to the battery

As soon as the app is set up, you can attach the battery guard to your battery. To do this, slightly loosen the terminal screws, place the battery clamps of the Battery Guard between the battery terminal and the screw, and then tighten the screws again. To ensure that your Battery Guard is secure, you can attach it to the battery using the double-sided adhesive pad provided. Please note that you will no longer be able to scan the barcode after this, but you can also find the serial number on the side of the Battery Guard.

You can find a detailed test report here:

https://www.grandcali.com/gadget-day-battery-guard/

GPSR Information

Name: Stefan Keckeisen Akkumulatoren e.K.

Address: Europastraße 9 87700 Memmingen

Email: info@intact-batterien.de

Website: https://www.intact-batterien.de

European Manufacturer: Yes

FAQ

How long will it take for my item to ship?

Shipping time always depends on the product group. For example, 3D printed products are manufactured to order, which means they are not stock items. The production time in this example is 10 to 14 business days.

If I have a question, how can I reach you?

It's very simple:

Either you send us an email to shop@zm-camping.de or you simply call us during our hotline hours at +49 2131 5954914.

We look forward to hearing from you!

Can I also pick up my order from you?

Unfortunately not, we are an online shop only and do not have a physical store.

For example, our warehouse is not located at our company address.

news

  • More water pressure in the Grand California, without issues with the control unit

    Mehr Wasserdruck im Grand California, ohne Ärger mit dem Steuergerät

    Many Grand California drivers wish for more water pressure in their Cali, be it for washing dishes or, especially, for showering.

    That's why many quickly get a stronger pump and install it. Unfortunately, the replacement isn't quite so simple. The Grand California, or rather its control unit, supplies power to the pump. A larger pump means greater power consumption, which is clear enough. However, you would also have to tell the control unit this, and that's precisely what isn't easily done.

    The result: Sometime after the replacement, perhaps not immediately, perhaps only in 2 weeks or 2 months, the pump stops pumping. The control unit thinks there's a problem because the current is higher than it should be. Usually, only a reset helps then, and the hope that it will fix the issue.

    This is exactly what happened to us on vacation. Our stronger Reich pump (25 instead of 19 liters per minute) simply stopped working, and nothing helped – no main switch, no reset, nothing. Luckily, we had an original 19-liter spare pump with us; we installed it, and the water immediately started flowing again.

    That annoyed us, so we built a solution ourselves. Our cable set solves the pump problem quickly and easily:

    • It's plugged in between the existing connectors, no cutting, no soldering on the VW harness
    • The original pump signal switches a relay (12 V/30 A) instead of directly loading the pump
    • The pump gets its power cleanly via an internal 15 A fuse
    • Your vehicle's electronics only see the small relay load and remain protected

    Nothing on the vehicle needs to be cut or destroyed; the installation is completely plug and play. Installation takes less than 5 minutes and works even without extensive technical know-how. The cable set is equipped with original Volkswagen connectors and therefore integrates perfectly, just like an original component.

    The cable set is available in our shop in two versions:

    1. Only the wiring harness (if you already have a stronger pump)
    2. With a Reich Power Jet Plus pump (25 liters per minute)

    Do you have any questions about the cable set? Just contact us, we'll be happy to help. And now, enjoy your shower.

     

    Continue reading
  • June Promotion: 15% off Eurobar Front Bars and ETB Side Steps

    Juni Aktion: 15% auf Eurobar Frontbügel und ETB Trittstufe

    Hey everyone!

    Summer is coming, and with it, the desire to improve your Grand California, Crafter or TGE. That's why we've picked out two parts for June that we really like, and we're giving you 15% off for the entire month. With the code ZMALPHA, you'll get the discount directly in your shopping cart.

    🛡️ Metec Eurobar Front Bar (VW Crafter and MAN TGE from 2017)

    A front bar not only looks great, but it can also do more. In tight parking spaces, on forest paths or in dense city traffic, the Eurobar absorbs the first impacts before they hit your Crafter or TGE. Made of 1.2 mm thick stainless steel tubing with a 70 mm diameter, matte black and with a vehicle-specific design for quick installation. It comes with EC type approval, so you don't have to worry about registration.

    🪜 AlphaDynamik ETB Swivel Step (Grand California)

    Tired of the original Thule step on your Grand California? Then this is your upgrade. 240 kg load capacity, LED lighting as standard and a smart swivel mechanism for the ideal entry height. The best part: We rely on the original AlphaDynamik control unit, so all functions are retained, including anti-trap protection and workshop mode. Our integration module is completely waterproof and sits protected under the driver's seat. Installation like from the factory, without loose cables and without provisional connections.

    What you need to know

    The 15% discount is valid until June 30th at 11:59 PM for exactly these two items. Simply enter the code ZMALPHA in the shopping cart and the discount will be applied. After that, prices will return to normal. So if you've been eyeing one of these parts for a while, now's the time.

    👉 Check out the shop and get your upgrade

    Best regards, Your ZM Team


    Please note: Depending on the order quantity, there may be delays in the delivery date. A subsequent discount is not possible; the code must be entered directly in the shopping cart when ordering. Payment via PayPal is not available for these two items; all other payment methods can be used as usual.

    Continue reading

Join the club ☕️

Sign up to our newsletter to receive updates about our future roasts!